• Новости

    Новости компании 3CX и партнеров

  • Релизы 3CX

    Анонсы о выходе новых или обновленных продуктов компании 3CX.

  • Статьи о 3CX Phone System

    Дополнительная документация и статьи о 3CX Phone System.

  • Настройка VoIP телефонов

    Инструкции по настройке VoIP / SIP телефонов для работы с 3CX Phone System.

  • Настройка VoIP шлюзов

    Инструкции по настройке VoIP / SIP шлюзов для работы с 3CX Phone System.

voip gateway

Configuring Topex Mobilink GSM Gateway with 3CX

January 16, 2012 - 2:49 pm | 0 Comments

IMPORTANT: This device has been tested for Voice using Firmware Version Mobilink-IP-1.2.13-C2P-SDX Setting up the Topex Mobilink IP Insert a SIM card into the Mobilink IP by opening the simtray by pressing the small yellow button with (for example) …

......Read More »

Outbound Rules – A Complete Example

July 20, 2010 - 9:44 am | 0 Comments

Configuring Outbound Rules on 3CX PhoneSystem is a very simple affair if you have a single device or service which you deliver calls with – in most cases a single rule will be enough. But the Outbound Rules in 3CX PhoneSystem allows you to create much more complex rules – allowing you to not only select backup routes which come into effect when other routes fail, but also to select a different set of routes, depending on the type of number being dialled. For the sake of this example, we will assume that our PBX: Has a Gateway connected to a 23-channel T1 circuit – best rates for local calls Has a 3CX SkypeGateway connection to reach Skype IDs directly from an extension Has a VoIP Provider account – this channel provides the best rates for international calls, but (in this example) requires the destination number to be presented in full international format, with the international prefix being “00″ Is using 3-digit extensions Has a Bridge connected to another 3CX PhoneSystem (which is also using 3-digit extensions) installed in London Emergency Number Probably the best way to handle the “911″ Emergency Number is to start with it

......Read More »

Configuring the Portech MV-370 and MV-372

April 26, 2010 - 7:16 am | 0 Comments

IMPORTANT This device has been tested for Voice using firmware version of “Wed Jun 10 11:53:59 2009”. The guide and template may not work for earlier or later versions of the firmware! Configuration is a 2 …

......Read More »

Configuring AVM FritzBox as a Firewall with 3CX Phone System

April 14, 2010 - 8:28 am | 0 Comments

This guide will show how to configure an AVM Fritzbox router / firewall as a border device with 3CX Phone System in the LAN. The tests were made using a FritzBox 7170 with firmware version …

......Read More »

How do I configure Tonesets for my Country on a Grandstream GXW-4104 / GXW-4108?

March 3, 2010 - 11:58 am | 0 Comments

NOTE: This device has been tested for Fax Calls and Voice Calls using firmware 1.2.1.5. Grandstream firmware versions are typically available from: http://www.grandstream.com/firmware.html. Depending on your geographic location and telecommunications provider, it may be necessary to update your Grandstream tone sets to reflect your location, or the specific requirements of your Telecommunications Provider

......Read More »

Updating a Beronet BeroFix VoIP Gateway to the latest firmware

December 5, 2009 - 1:11 pm | 0 Comments

If you are not using firmware “appfs-1.12rc9x.tar.gz” please update your your card to the latest version as explained below. Update Procedure To update go to http://www.beronet.com/downloads/berofix/ and download the appropriate update. Log on to the beroFix Webinterface, click …

......Read More »

Debugging calls on a Patton Smartnode

November 3, 2009 - 1:13 pm | 0 Comments

You can do simple debugging (for ISDN, for example) on a Patton gateway by using a series of simple commands. After connecting to the gateway via telnet, type the following: login: {your username here} password: {password here} enable configure debug ccisdn …

......Read More »

How do I update a Patton Smartnode to the latest firmware?

October 3, 2009 - 12:38 pm | 0 Comments

This document explains step by step how to upgrade the firmware of your Patton to the latest version. This doc uses the Patton 4554 as an example, however all other Patton devices follow an almost …

......Read More »

How can I adjust the configuration for unsupported VOIP providers or gateways?

July 5, 2009 - 10:20 am | 0 Comments

How can I adjust the configuration for unsupported VOIP providers or gateways? 3CX performs extended tests with a number of VoIP Providers and Gateways

......Read More »

How do I configure Patton ISDN VOIP Gateways for a Point-to-Point Connection?

April 3, 2009 - 12:47 pm | 0 Comments

This article applies to ISDN lines and ISDN gateways only. An ISDN line can either be point-to-point or point-to-multipoint

......Read More »

What Call Progress Tones should I enter for my country?

March 1, 2009 - 6:42 am | 0 Comments

Call Progress tones are audible tones used  by the public switched telephone network (PSTN) central office or a private branch exchange (PBX) to signal calling parties the status of phone calls.

......Read More »

How to test a VoIP gateway

March 1, 2009 - 6:38 am | 0 Comments

General Reset gateway to factory default and ensure you are running the latest firmware. Review vendor documentation and assign a IP / Subnet mask / default router or gateway / DNS entries to the device.

......Read More »

Switch to our mobile site